MTD E6C3H Manual del operador Pagina 1

Operator's ManualSnow ThrowerModel E6C3HIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWarning: This unit is equipped with an internal co

SECTION5: MAKINGADJUSTMENTS,_ WARNING: NEVER attempt to make anyadjustments while the engine is running,except where specified in the operator'sm

ShiftRodAdjustmentTo adjust the shift rod, proceed as follows:• Remove the hairpin clip and slide the shift rodconnector up, to separate the upper shi

wheel hub.This position gives power drive to the leftwheel only, making the unit easier to maneuver.BothWheelsDriving• Rotate wheel assembly to align

TractionControl / AugerControl LockThe cams on the ends of the control rods whichinterlock the traction drive and auger drive controlsmust be lubricat

• Drain the gasoline from the snow thrower, or placea piece of plastic film under the gas cap.• Tip the snow thrower up and forward so that it restson

Hex Nut /Bell WasherFigure 19• Remove the four screws from the friction wheelassembly. Remove the friction wheel rubber frombetween the friction wheel

SECTION8: TROUBLESHOOTINGTrouble Possible Cause(s)Engine fails to start Fuel tank empty, or stale fuel.Engine runs erraticBlocked fuel line.Choke not

ModelE6C3H111333Ref,No,1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.Part No. Part Description618-0123618-0124710-0642711-0124A714-0161715-0143717-0528A71

ModelE6C3H656367__6O134143149\1412558524576781115028411868-_" /06927836427 7272277169688418

ModelE6C3HRef,No,1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.30.31.32.35.38.39.40.41.42.Part No.684-0008A710-0458710-04

TABLEOFCONTENTSContent PageImportant Safe Operation Practices ... 3Assembling You

ModelE6C3H%151411 10122 14 3 _ "/53818>36 4137 l313/ 434220

ModelE6C3HRef,Pa_ No.No.1. 712-01162. 756-01783. 784-5632B4. 710-0459A5. 738-02816. 736-01677. 732-06118. 712-30689. 710-027610. 736-011911. 05931A12.

ModelE6C3H26L L1/2211611619161115 \910 \14720IMPORTANT: For a proper working machine, use FactoryApproved Parts.V-BELTS are specially designed to enga

ModelE6C3HRef,No,1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.Part No. Part Description710-1652731-1324732-0

ModelE6C3H20<461311126 A 36BlowerHousing1042Drive ClutchCableAuger ClutchCable12814l 415Auger ClutchCable24

ModelE6C3HRef,Part No.No.1. 710-05992. 784-56883. 784-5687A4. 756-06255. 738-09246. 784-5630B7. 741-05638. 736-01059. 712-011610. 741-059811. 736-0188

Notes26

27

MANUFACTURER'S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SECTION1: IMPORTANTSAFEOPERATIONPRACTICESThis symbol points out important safety instructions, which if not followed, could endanger the personalsafet

4. Neveroperatewithamissingordamageddischargechute.Keepallsafetydevicesinplaceandworking.5. Neverrunanengineindoorsorinapoorlyventilatedarea.Engineexh

SECTION2: ASSEMBLINGYOURSNOWTHROWERNOTE: References to right or left side of the snowthrower are determined from behind the unit in theoperating posit

SECTION3: KNOWYOURSNOWTHROWERTraction Control/ Lever-Auger ControlHeadlightDischarge_ /ChuteA!Shoeger Drive ControlDirectionalControlm_-"=_ ;anio

HeadlightThe headlight is on whenever the engine is running.ThrottleControlThe throttle control is located on the engine. It regulatesthe speed of the

• Whendisconnectingthepowercord,alwaysunplugfromthethree-prongreceptaclefirstandthenfromthesnowthrower.RecoilStarter• Rotate choke knob to FULL choke

RepeatAugerControlTesttoverifyproperadjustmenthasbeenachieved.AugerCustomer Support as instructed on page 2 forinformation regarding price and availab