MTD E600E Manual del operador

OPERATOR’S MANUALIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722Warning: This unit

10Figure 11It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing

11• Crank clockwise to discharge to the left.• Crank counterclockwise to discharge to the right.Throttle Control The throttle control is located on th

12• Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly.• Pull starter handle rapidly. Do not allow

13To Engage Augers To engage the augers and start the snow throwing action, squeeze the auger control against the left handle. Release to stop the aug

14underneath the snow thrower by removing six self-tapping screws.With the traction control released, there must be clearance between the friction whe

15Figure 21Gear ShaftLubricate the gear shaft with a good all-weather multi-purpose light grease at least once a season or after every 25 hours of ope

16600/610E has only one auger belt).• Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 22.

17Figure 25Changing Friction Wheel RubberThe rubber on the friction wheel is subject to wear and should be checked after 25 hours of operation, and pe

18SECTION 10: TROUBLE SHOOTING GUIDETrouble Possible Cause(s) Corrective ActionEngine fails to start Fuel tank empty, or stale fuel.Blocked fuel line

19Models E600E, E610E, E640F, E660G, and E6C0FREF.NO.PARTNO. DESCRIPTION1 618-0123 RH Reducer Housing2 618-0124 LH Reducer Housing3 710-0642 Hex Screw

2TABLE OF CONTENTSContent PageImportant Safe Operation Practices...3Loose Parts &

20Models E600E, E610E, E640F, E660G, and E6C0F123456789101112141513161091819202122231325232226182728133030313231323316183536373839414042434039444534

21Models E600E, E610E, E640F, E660G, and E6C0FREF.NO.PARTNO. DESCRIPTION1 712-0116 Lock Jam Nut 3/8-242 756-0178 Flat Idler 3 784-5632A Auger Idler Ar

22Models E600E, E610E, E640F, E660G, and E6C0F11223345671891031113121431516171819201819202121222324252627282930313233343520363738403941352043444527264

23Models E600E, E610E, E640F, E660G, and E6C0FREF.NO.PARTNO. DESCRIPTION1 714-0507 Cotter Pin2 747-0877 Rod3 710-0599 Hex Washer Screw 1/4-20 x .54 78

24Models E600E, E610E, E640F, E660G, and E6C0F11234455616” Wheels13” or 15” Wheels47789101011111215131415161718119202122232425252628292611303132333483

25Models E600E, E610E, E640F, E660G, and E6C0FREF.NO.PARTNO. DESCRIPTION1 710-1652 Hex Screw 2 784-5688 Drive Cable Guide Bracket3 784-5687A Auger Clu

26E600E, E610EREF.NO.PARTNO. DESCRIPTION1 710-1652 Hex Washer Screw 1/4-20 x.52 731-1324 Belt Cover3 732-0339 Extension Spring4 710-0627 Hex Screw 5/1

27E640F, E660G, and E6C0FREF.NO.PARTNO. DESCRIPTION1 710-1652 Hex Washer Screw 1/4-20 x .6252 731-1324 Belt Cover3 732-0710 Extension Spring4 710-0627

MANUFACTURER’S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTDPRODUCTS INC (“MTD”) with respect to new merchandisepurchased

3SECTION 1: IMPORTANT SAFE OPERATION PRACTICESThis symbol points out important safety instructions which, if not followed, could endanger the persona

44. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working.5. Never run an engine indoors or in a poorl

5SECTION 2: LOOSE PARTS & HARDWARE PACKIMPORTANT:After assembly, service engine with gasoline, and check oil level as instructed in the separate

6Contents Of Hardware PackLay out the hardware according to the illustration for identification purposes. Part numbers are shown inparentheses. (Hardw

7SECTION 3: ASSEMBLING YOUR SNOW THROWERWARNING: Disconnect the spark plugwire and ground it against the engine toprevent unintended starting.NOTE:

8Attaching The Chute Assembly (Hardware C)Place chute assembly over chute opening, with the opening in the chute assembly facing the front of the unit

9• Thread the ferrule onto the shift rod until the ferrule lines up with the upper hole in the shift lever (beneath the handle panel). Insert the ferr