MTD 21AA413H700 Manual del operador

Operator's ManualRear Tine TillerModel Series 410IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWarning: This unit is equipped with an in

SECTION4: OPERATINGYOURTILLER,_ WARNING: Read, understand, and followall instructions and warnings on themachine and in this manual beforeoperating.Be

• When using the tiller for the first time, use thesecond adjustment hole from the top (1" of tillingdepth). See Figure 9.Use This Position _Firs

SECTION5: MAKINGADJUSTMENTS_, WARNING: Never attempt to make anyadjustments while the engine is running,except where specified in operator'smanua

SECTION6: MAINTAININGYOURTILLER_, WARNING: Disconnect the spark plug wireand ground it against the engine beforeperforming any repairs or maintenance.

NOTE:Upon reassembly, make certain the belt isrouted over the idler pulley and inside of belt keepers byengine pulley. See Figure 10.I EnginePulley Be

SECTION7: TROUBLESHOOTINGGUIDEPossible Cause(s)Fuel tank empty, or stale fuel.TroubleEngine fails tostartEngine runserraticEngine overheatsTines do no

SECTION8: PARTSLISTFORMODELSERIES410581232829\ I321\162526 3,1835IIIi 41II194O3916

ModelSeries410Ref.Part No.No.1. 710-10172. 786-01683. 686-00954. 712-040635. 715-01206. 786-01177. 710-30088. 712-30109. 736-024210. 710-318011. 710-1

ModelSeries410323638924252313\\322518

ModelSeries410Ref.Part No.No.1. 721-03782. 712-03783. 736-04074. 721-03795. 716-08656. 686-00387. 618-0245B9. 713-023310. 750-057011. 736-016312. 750-

This Operator's Manual is an important part of your new tiller. It will help you assemble, prepareand maintain the unit for best performance. Ple

ModelSeries4103/1o_-7231025_/ 2617J jJJJJJ J _1 JJJ JJJJ\/v3217 42_4320

ModelSeries410Ref.No.1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.Part No.710-1017786-0131710-0896720-0278A735-0246647-0014786-01187

NOTES22

NOTES23

MANUFACTURER'S LIMITED WARRANTY FOR:The limited warranty set forth below is given by MTD LLC withrespect to new merchandise purchased and used in

SECTION1: IMPORTANTSAFEOPERATIONPRACTICESWARNING: This symbol points out important safety instructions which, if not followed, couldendanger the perso

7. Neveroperatethemachineathightransportspeedsonhardorslipperysurfaces.8. Exercisecautiontoavoidslippingorfalling.9. Lookdownandbehindandusecarewhenin

SECTION2: ASSEMBLINGYOURTILLERNOTE: This operator's manual covers various modelsof tillers. The units illustrated may vary slightly fromyour unit

Retainer BracketShoulder Bolt & Lock NutFigure 3• Place the hex opening of the flange nut retainerbracket over the flange nut securing the handlea

• Remove one hex nut from the threaded casing onthe end of the cable. Slip the wire up through theslot on the cable bracket underneath the handle.• Pu

SECTION3: KNOWYOURTILLERHandleHandleHandle Adjustment_HandleStakeModel 410 SeriesFigure 8WARNING: Read, understand, and follow Reverseall instructions

ChokeLever(if Equipped)The choke lever is located on top of the carburetor onthe back of the engine underneath the muffler. It is usedto enrich the fu