MTD TrimmerPlus TB720r Manual del operador descargar pdf (Pagina 7)

CAUTION: The add-ons with the coupler

system are to be used in the primary hole

only unless stated otherwise in the specific

add-ons operator’s manual. Using the wrong

hole could lead to personal injury or damage

to the unit.

For edging when using the straight shaft trimmer add-

on, lock the release button of the cutting attchment into

the 90° edging hole or the 180° edging hole (Fig. 3).

Check Flex Shaft Engagement Prior to Using

1. Start the unit.

2. Briefly engage and release the trigger.

3. Check that add-on is operating.

4. If the add-on is not operating, remove add-on and

repeat steps for installing the add-on.

5. Recheck operation of add-on attachment.

ASSEMBLING THE COUPLER

The TrimmerPlus® system enables the use of these

optional add-ons.

Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . BV720r

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . HS720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Sweeper/Blower . . . . . . . . . . . . . . . . . . . . . . . . . SB720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

WARNING: Read and understand

operator’s manual for unit to be used with

this add-on prior to operation.

Removing the Add-Ons:

1. Turn the knob counterclockwise to loosen (Fig. 1).

2. Press and hold the release button (Fig. 1).

3. While firmly holding the upper shaft housing, pull the

add-on straight out of the coupler. (Fig.2)

Installing the Add-Ons:

WARNING: To avoid serious personal injury

and damage to the unit, shut unit off before

removing or installing add-ons.

NOTE: To make installing or removing the add-on easier,

place the unit on the ground or on a work bench.

1. Remove the hanger from the top of the lower shaft

housing.

2. Turn the knob counterclockwise to loosen (Fig. 1).

3. While firmly holding the add-on, push it straight into

the coupler (Fig. 2).

NOTE: Aligning the release button with the guide recess

will help installation (Fig. 1).

3. Turn the knob clockwise to tighten (Fig. 3).

CAUTION: Lock the release button in the

primary hole and securely tighten the knob

before operating this unit.

Fig. 1

Fig. 2

Fig. 3

Primary Hole

Upper Shaft Housing

Coupler

Lower Shaft Housing

Release Button

Knob

90° Edging Hole

180° Edging Hole

Coupler

Release Button

Guide Recess

Knob

ClockwiseCounterclockwise

OPERATING INSTRUCTIONS

1 2 3 4 5 6 7 8 9 10 11 12 ... 47 48

Comentarios a estos manuales

Sin comentarios

MTD TrimmerPlus TB720r Manual del operador Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Cortadoras De Césped MTD TrimmerPlus TB720r