MTD 390 Shown Manual del operador

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USASafe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshoot

Push the chute control rod toward the control panel until 7. the hole in the rod lines up with the hole in the chute control input closest to the chut

Overhead Chute Control AssemblyHandle AssemblyPlace the shift lever in the Forward-6 position.1. Observe the lower rear area of the snow thrower to be

Finish securing chute control assembly to chute support 3. bracket with wing nut and hex screw removed earlier. See Fig. 3-14.Insert the chute direct

NOTE: Make certain the cables are seated properly in the roller guides. See Fig. 3-18.Secure the handle by tightening the plastic knob located 2. on b

U-Joint Crank AssemblyHandlePlace the shift lever in the forward-6 position.1. Observe the lower rear area of the snow thrower to be sure 2. both cabl

Set-UpShear Pins Storage (if so equipped)A pair of replacement auger shear pins and bow tie cotter pins are included with your snow thrower. If your s

AdjustmentsChute Assembly NOTE: Upper chutes on models with 4-Way Chute Control are also controlled by the Chute Directional Control. See Fig. 4-1.The

Auger ControlWARNING! Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your s

Snow thrower controls and features are described below and illustrated in Fig. 4-1. Shift Lever (If so Equipped)The shift lever is located on the han

Drift Cutters (If so Equipped)The drift cutters are designed for use in deep snow. Their use is optional for normal snow conditions. Maneuver the snow

Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.If you have diffic

2-Way Chute Directional Control (If so Equipped)The chute directional control is located on the left side of the dash panel.To change the direction in

Starting and Stopping the EngineRefer to the Engine Operator’s Manual packed with your snow thrower for instructions on starting and stopping the engi

MaintenanceEngineRefer to the Engine Operator’s Manual packed with your snow thrower.Tire PressureRefer to the Assembly & Set-up section for infor

Auger ControlRefer to the Assembly & Set-up section for instructions on adjusting the auger control cable.Skid ShoesRefer to the Assembly & Se

Chute Bracket Adjustment (If so Equipped)If the spiral at the bottom of the chute directional control is not fully engaging with the chute assembly, t

Service725Belt ReplacementAuger BeltTo remove and replace your snow thrower’s auger belt, proceed as follows:Allow the engine to run until it is out o

26 se c t i O n 7 — se r v i c eRemove the belt from around the auger pulley, and slip the 7. belt between the support bracket and the auger pulley.

27se c t i O n 7 — se r v i c eBack out the stop bolt to increase the clearance between 6. the friction wheel disc and friction wheel. See Fig. 7-7.S

28 se c t i O n 7 — se r v i c eCarefully remove the hex nut which secures the hex shaft 5. to the snow thrower frame and lightly tap the shaft’s end

Troubleshooting829Problem Cause RemedyEngine fails to start Choke not in CHOKE position.1. Spark plug wire disconnected.2. Fuel tank empty or stale fu

Important Safe Operation Practices23TrainingRead, understand, and follow all instructions on the 1. machine and in the manual(s) before attempting to

Component Part Number and Description929-0071A† Extension Cord, 110V954-04050 Auger Drive Belt (22”, 24” & 26”)954-04260 Wheel Drive Belt (22”,

The following attachments and accessories are available for your snow thrower. Phone (800) 800-7310 for information regarding compatibility, price and

MANUFACTURER’S LIMITED WARRANTY FORGDOC-100016 REV. CThe limited warranty set forth below is given by MTD LLC with respect to new merchandise purchase

4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafe Handling of GasolineTo avoid personal injury or property damage u

5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sClearing a Clogged Discharge ChuteHand contact with the rotating impell

6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may

Contents of CartonOne Snow Thrower• Two Replacement Auger Shear Pins• One Product Registration Card• One Chute Control Rod (if so • equipped)One Sno

Figure 3-1Figure 3-22-Way & 4-Way Assembly Remove all loose parts before assembling.Handle AssemblyPlace the shift lever in the Forward-6 position

Place chute onto chute base and ensure chute control 3. rod is positioned under the handle panel. Install hex bolt previously removed but do not secur