MTD 27-Ton Manual del operador descargar pdf (Pagina 9)

• Tolockthebeamintheverticalposition,pullouton

theverticalbeamlockandrotateit tosecurethe

beam.SeeFigure7.

• Standinfrontoftheunittooperatethecontrol

handleandtostabilizethelog.SeeFigure8A.

Figure 8

HorizontalPosition

• Pull the vertical beam lock out and rotate it down.

See Figure 7. Pivot beam to the horizontal position.

The beam will lock automatically in horizontal

position.

• Stand behind the reservoir tank to operate control

handle and to stabilize the log. See Figure 8B.

OperatingTips

Always:

1. Use clean fluid and check fluid level regularly.

2. Use Dexron III Automatic Transmission Fluid or

10W AW hydraulic fluid.

3. Use a filter (clean or replace regularly)

4. Use a breather cap on fluid reservoir.

5. Make sure pump is mounted and aligned properly.

6. Use a flexible"spider" type coupling between

engine and pump drive shafts.

7. Keep hoses clear and unblocked.

8. Bleed air out of hoses before operating.

9. Flush and clean hydraulic system before restarting

after servicing.

10. Use "pipe dope" on all hydraulic fittings.

11. Allow time for warm-up before splitting wood.

12. Prime the pump before initial start-up byturning

over the engine with spark plug disconnected.

13. Split wood along the grain (lengthwise) only.

Never:

1. Use when fluid is below 20° F or above 150° F.

2. Use a solid engine/pump coupling.

3. Operate through relief valve for long.

4. Attempt to adjust unloading or relief valve settings

without pressure gauges.

5. Operate with air in hydraulic system.

6. Use teflon tape on hydraulic fittings.

7. Attempt to cut wood across the grain.

8. Attempt to remove partially split wood from the

wedge with your hands. Fully retract wedge to

dislodge wood with log dislodger.

RaisingandLoweringBeam

• Use control handle to run wedge up and down

beam 6 to 8 times to circulate the hydraulic fluid,

which will warm and thin the fluid.

• Place log splitter on a firm, level surface.

• To raise the beam for vertical operation: Pull out

the vertical beam lock on the tongue.

• Pivot beam lock down to release the beam.

• Move the beam to the vertical position. Secure it

with the beam lock on the reservoir tank assembly.

_ib ARNING: Always use the log splitter in the

vertical position when splitting heavy logs.

To lower the beam: Pull out the horizontal beam

lock on the reservoir tank.

Pivot beam lock down to release the beam.

Carefully pull back on beam and lower it to the

horizontal position.The horizontal beam lock will

lock automatically. See Figure 7.

Transportingthe LogSplitter

IMPORTANT:Always turn fuel valve to OFF position

before transporting the log splitter.

• Lower the beam to its horizontal position. Make

certain the beam is locked securely with the

horizontal beam lock.

• Remove spring clip and clevis pin from jack stand.

• Support the tongue and pivot the jack stand up

against the tongue. See Figure 9.

Tongue Clevis Pin _

Jack Stand

Figure 9

Secure with the spring clip and clevis pin previously

removed. See Figure 9.

Attach coupler hitch to a class I or higher 2" ball on

a towing vehicle; latch securely.

a, If coupler hitch does not fit on ball: Turn

adjustment nut one turn counter-clockwise.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

MTD 27-Ton Manual del operador Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Cortadoras De Troncos MTD 27-Ton